Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

51-532 Knobs
#1

Hello, I'm new here this is my first post, need both knobs for this radio 51-532 any ideas.
Thanks
Jim

Jim
Spring Lake MI
#2

Welcome to the Phorum!
Icon_wave

You can try a couple of approaches for those knobs.  
1) Check with the folks that are in the knob business.  I've used most of the people on the lists found on this page in the Resources section.
You may need to send a picture of the knobs you are looking for.  Some photos can be found on the Gallery pages.

2) Post in the Wanted Ads section and you may find someone has a set or some spare knobs.
#3

(07-28-2016, 08:51 AM)klondike98 Wrote:  Welcome to the Phorum!
Icon_wave

You can try a couple of approaches for those knobs.  
1) Check with the folks that are in the knob business.  I've used most of the people on the lists found on this page in the Resources section.
You may need to send a picture of the knobs you are looking for.  Some photos can be found on the Gallery pages.

2) Post in the Wanted Ads section and you may find someone has a set or some spare knobs.
Thanks
#4

Found some.




Users browsing this thread:
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 2111 online users. [Complete List]
» 3 Member(s) | 2108 Guest(s)
AvatarAvatarAvatar

>