Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

ID this Radio?
#1

Can anyone help ID this radio?

"Ignorance is bliss...'til you have to fix a radio..."
#2

DId you browse through the GALLERY section on this site yet??
That's the Lowboy version cabinet used for for a Models 65, 87, 40, 76, 95.
Mid-1929 to 1930.

Yours has obviously been stripped of original finish. Good shape otherwise.

Chuck
#3

Thanks Chuck. I actually had this picture sent to me by my brother who saw it in an upcoming auction this weekend. The cabinet does look good aside from the refinishing job, no clue what's actually inside. I'm new to the collecting trade -- do you know if this model is very common, collectible, etc? I appreciate your quick reply! Joe Icon_biggrin

"Ignorance is bliss...'til you have to fix a radio..."
#4

Very collectable, but it looks like it's ONLY the cabinetry. No radio chassis. I see no control shafts in the holes.
Someone probably gutted and stripped the cabinet and was using it as furniture. (?)

Not a good deal if not complete. You may have a long while to acquire a chassis of appropriate model to fill it.
#5

Thank you - I appreciate the help. Hopefully, there's a chassis that accompanies it!

"Ignorance is bliss...'til you have to fix a radio..."
#6

Don't worry, there are plenty of chassis that will fit (65, 87, 76, 95). I probably have more than one kicking around here in restorable condition. They are heavy buggers, though.

--
Ron Ramirez
Ferdinand IN
#7

Yes, great looking cabinet.
#8

Thanks guys. Yes, I'm pretty intrigued by this cabinet and its condition. As much more experienced collectors than I, any suggestions on what a max auction value would be for just the cabinet? The estate sale is tomorrow and my brother's waiting on direction from me. My plan would be to refinish the cabinet back to original state (with Ron's advice on proper Mohawk toner colors) and then find a chassis to add.

Any advice is much appreciated.

"Ignorance is bliss...'til you have to fix a radio..."
#9

I'm happy to report I got the cabinet at the auction for $10 Icon_eek Unbelievable. Small piece of veneer in the front grid to repair and I'm going to refinish to original colors, but think I did pretty well...

"Ignorance is bliss...'til you have to fix a radio..."
#10

jayoungs Wrote:I'm happy to report I got the cabinet at the auction for $10 Icon_eek Unbelievable. Small piece of veneer in the front grid to repair and I'm going to refinish to original colors, but think I did pretty well...
That's an awesome price. I bet you end up with a real jewel once this thing is refinished and holding a restored chassis.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1894 online users. [Complete List]
» 3 Member(s) | 1891 Guest(s)
AvatarAvatarAvatar

>