Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
All My next attempt ... Its a Zenith 5D011 Consoltone radio. Looks pretty good..
[Image: http://i292.photobucket.com/albums/mm38/...tg11oa.jpg]
The Grill cloth is a little dirty...
In sides not to bad pretty open..
[Image: http://i292.photobucket.com/albums/mm38/...wggurw.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...vzcc25.jpg]
I hope all Coils and IF's are OK.. Thats the next checks.. Then test tubes..
More to follow...
Skip...
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Ok, All coils and IF caps and Output Transformer check out OK..
I did notice a wrong value of resistor in radio Its R6 I think Value 220 Ohms.. There is a 1K resistor in there.. Not really sure if it is original...
Will it make any difference?
[Image: http://i292.photobucket.com/albums/mm38/...yza9hn.jpg]
Skip...
Posts: 4,442
Threads: 419
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
Neat set, a brown version of this is featured in a late 3 Stooges, with Shemp. They are income tax preparers, the red lite when on is cool. Good luck.
Paul
Tubetalk1
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
All, As I was recapping I found this.. Its C3 .05 uf to ground. Parts list says its a .05 200 Volt.. However whats in it is a .05 at 1000 Volts.. Is that a replacement that someone had ?? Or original..
Here are pictures...
[Image: http://i292.photobucket.com/albums/mm38/...zqlmwf.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...2eipxe.jpg]
Actual Part...
[Image: http://i292.photobucket.com/albums/mm38/...hhvxpp.jpg]
Thanks
Skip...
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Ok, Since no answers.. I put together 2 .1 600 Volt caps in series to make a .05 at 1200 Volts and put in ..
Finished wiring up the E-Caps and tomorrow will power it up..
Skip..
Posts: 16,510
Threads: 572
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
200V is more than enough.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
You might want a high voltage cap in that location. It connects between the chassis and AC line.
Depending on which way the line cord is plugged in, its either neutral or hot connected to the chassis if the cap shorts.
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale
State, Province, Country: PA
Ok, Thanks all.. Completed the Caps and resistors replacement. Plugged in and brought up slowly. At 117 Volts draws .25 amps.. Radio plays and picks up many stations.. On to alignment as dial is off a little..
Skip...
Posts: 670
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
Wow,,,there must be 3 ,,,R-6's,,,there are 2 together,,,470,000 ohms,,,thee other may ?? be a mistake , (Label) ,better Check you parts list closely,,,CHEERS
Posts: 670
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
on Zenith 6D015---R-3 is 1000 ohms----which is in the SAME location off the tube 12SA7GT of YOURS ( R-6,,220 ohms resistor),,which READS 1K,, CHEERS again
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco model 38 code 121 not receiving signal.
|
| So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM |
|
462ron
|
|
It’s on the bottom of the homepage of our Philcoradio.com homepage!
Ron462ron — 07:20 AM |
|
Model 70 Cabinet Trim
|
| Steve might have some trim left.
Not sure he is making anything.morzh — 06:12 AM |
|
Model 70 Cabinet Trim
|
| Hello musar,
First all welcome to the forum and yes that is true that steve stopped making trim .
Sincerely Richar...radiorich — 12:13 AM |
|
Model 70 Cabinet Trim
|
| I have recently come into possession of a Model 70. The trim around the base needs to be replaced. If this were years ...musar — 12:07 AM |
|
philcorepairbench.com - shadow-meter
|
| Anyone know of a way to recover these files from the repair bench? Thanks.
fenbach — 11:16 PM |
|
Philco model 38 code 121 not receiving signal.
|
| That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM |
|
Philco model 38 code 121 not receiving signal.
|
| A DMM is good enough.
One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now.
Have better volu...murf — 03:43 PM |
|
Philco model 38 code 121 not receiving signal.
|
| I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM |
|
Who's Online
|
There are currently 1339 online users. [Complete List]
» 2 Member(s) | 1337 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
