Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Masterpeice V Correct?
#1

http://www.radiomuseum.org/r/mcmurdo_masterpiece_v.html


Is this listing correct? In particular the picture of the 2 12" Jensens + tweeter mounted on a new looking baffle. And the text that also mentions the 2 Jensens?

I have been told that this may have been correct for the MPIV but the only speaker for the MPV was the 18" Jensen.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#2

That's what you get for going to that website Icon_lol

But seriously...I'm no Silver expert but I have never heard of an MP V using anything but the 18 inch Super-Giant Jensen speaker. Now, the dual field coils used in the MP V speaker has a different DC resistance than the dual fields in the MP VI speaker, but both are 18 inch Jensens.

I would like to see that photo up close...I suspect all of those stickers on the backs of the speakers are reproductions.

If you can contact Y2KBruce, he can tell you more about it. He knows more about those sets than I do.

--
Ron Ramirez
Ferdinand IN
#3

Yep. Norman B. down in Redding says the same thing. He has seen more than a few of them.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

Yes, Norman, of course. He is VERY knowledgeable in all things McMurdo and Scott. If he says the MP V only used the Super-Giant, then it's so.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM

[-]
Who's Online
There are currently 1280 online users. [Complete List]
» 2 Member(s) | 1278 Guest(s)
AvatarAvatar

>