Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
Fellow Philco Phans 
I'd appreciate some help.
I just picked up this 1936 620F, and it has been worked on. Most noticeably, the grill cloth  . I plan to replace it, but the backing is a flimsy cardboard. 
Would anyone happen to have this or a similar model that would be so kind as to get a tracing or a good quality pic of the original grill board for me 
[Image: https://farm5.staticflickr.com/4207/3554...6d9c_k.jpg]
[Image: https://farm5.staticflickr.com/4257/3484...4c3a_k.jpg]
Thanks in advance!
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Not sure if this will help at all, as it's a model 625, which may or may not have the same backing board, but this reassembly video shows how it looks beginning at around the 6:40 mark:
https://www.youtube.com/watch?v=tCkg_QaDCno
Greg V.
West Bend, WI
Member WARCI.org
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
This will do! Thank you very much! 
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
One more Question: I'm in the process of recapping, and need to know the values of the tone control. Part No. 30-4316.
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Looks like 0.02 or could be 0.01 kind of hard to tell. and 3 or 5000 uuf. 61 & 61a on schematic.
http://www.nostalgiaair.org/pagesbymodel...013804.pdf
(This post was last modified: 07-03-2017, 09:54 PM by KCMike.)
Posts: 1,889
Threads: 214
Joined: May 2015
City: Seattle
State, Province, Country: WA
It's a bit clearer on this scan of service bulletin 218A:
https://drive.google.com/file/d/0B64cfWa...sp=sharing
0.02uF in the tone control for 61.
0.003uF tubular for 61a.
BTW - nice radio Jeff!
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
Thanks Nathan!
Hopefully this 620 will go smoother than my 1st!
Took me 13 months to get my 1st up and running. 
So far it's going well.
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
I made this video a couple nights ago. It's up and running.  I have a reproduction dial on order from Radio Daze, and a grill cloth from Richmond Designs . I'll wait until I get the dial in before doing the alignment, as the one on there now is incorrect. 
[Video: https://youtu.be/vzbKkz7eZyc]
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Users browsing this thread:
|
|
Recent Posts
|
|
Philco model 38 code 121 not receiving signal.
|
| That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM |
|
Philco model 38 code 121 not receiving signal.
|
| A DMM is good enough.
One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now.
Have better volu...murf — 03:43 PM |
|
Philco model 38 code 121 not receiving signal.
|
| I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM |
|
Philco model 38 code 121 not receiving signal.
|
| I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM |
|
Philco model 38 code 121 not receiving signal.
|
| Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM |
|
Philco model 38 code 121 not receiving signal.
|
| It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM |
|
Philco model 38 code 121 not receiving signal.
|
| I've reinstalled the coil. Now IT'S ALIVE!!!!!!
I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM |
|
Philco model 38 code 121 not receiving signal.
|
| Yes, Walmart, right up there with Fluke.RodB — 11:00 AM |
|
PT 6 chassis screws size???
|
| it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM |
|
Who's Online
|
There are currently 1928 online users. [Complete List]
» 3 Member(s) | 1925 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
