Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-84
#1

Started working on Philco 37-84 the other day....Very nice radio and in good shape. Seems someone has changed out this volume control at some point. Print calls for a 20K pot and I am measuring over 2meg on the winding. It is a Philco part but don't believe it's the original part (maybe I'm wrong). Seems I get nothing out of the speaker until I turn control more than half way and then there is little adj. left. Also found the parts list had a mistake with a resistor value. The print show it as being a 240K resistor but the parts list show it as a 24K (this is resistor #22). Trying to find resistors with the same values as on the print are sometimes difficult so I just add, parallel resistors to get the proper value for the ones that are WAY out of tollerance.

Is there anyplace I could purchase a CORRECT volume/on-off switch for this unit and also, the tuner Dial needle is missing. Yes I could rig something but would like the original look (which I have NO IDEA what that is).

Nice to have found this site being from Philly and knowing where the old Philco factory was when I was a kid...and YES I have been to Evansville Indianna.

Gottagojoe
#2

See all the supplier's links on the FAQ and RESOURCE LINKS pages of my site. Icon_smile
#3

Been to your site (actually happened upon it a few weeks ago), you have a 5056 volume control listed, mine is a 5055 20K with on/off switch. Any chance someone has one of these around?? Hate to put a crappy radio shack pot in a classic radio.
gottagojoe
#4

the volume control on my philco 37-84 is 006317 part number but I know it CAN'T be the original.

Gottagojoe




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM
Philco model 38 code 121 not receiving signal.
Good news everyone! I think I have found everything I need for rewinding the antenna coil primary. I found some pla...Stormlord5500 — 09:40 AM
Philco Battery-WWII vintage
My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM
Philco Battery-WWII vintage
Hello Bob, What Amazing find! Sincerely Richardradiorich — 10:19 PM
Testing a speaker and output transformer Trutone A2-G
Hi Murf, Do this: Monitor between ground and one plate of the rectifier while playing the radio.  Do the same with ...MrFixr55 — 09:51 PM
Philco Battery-WWII vintage
Mike; I take it that Soviet cars did not come equipped with block heaters, hence the hot oil change? Where I lived in...Arran — 08:42 PM
Philco 42-345 Restoration/Repair
The more the better. (Within reasonable limits.) 2-5 times more is no problem in this case.Vlad95 — 03:50 PM
Philco 42-345 Restoration/Repair
Thanks, RodB and Vlad95, I was mainly trying to figure out this capacitor to locate a replacement, Vlad thank you for...osanders0311 — 03:44 PM

[-]
Who's Online
There are currently 916 online users. [Complete List]
» 2 Member(s) | 914 Guest(s)
AvatarAvatar

>