Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89 (code 121) parts list
#1

I have looked for this and hope I haven't missed it somewhere. Can anyone point me to a parts list for the Philco 89 Code 121 cathedral? There is a bottom view of the chassis showing parts in Riders 3-34 with the schematic on 3-33, but I cannot find a page telling me what the actual parts are. I am mainly wanting to know the capacitors before pulling the blocks out. I know I can look at the block numbers and figure it out, but sometimes you have to pull it to see the numbers. I see a parts list for the 89 code 123, but numbers are different.
Thanks,
Scott
#2

Welcome to the Phorum! Icon_wave

Here's a must view link: http://www.philcoradio.com/phorum/showth...?tid=15002 that has the evolution of the model 89 showing the changes in the circuits over the years. Ron, our founder, put this together and should be very helpful. It does not have a list of parts but the schematics are very readable.

Also try: http://www.audiophool.com/Philco.html where you can view Service Bulletins #146 and #146B. They have lists for the 121 and 123 respectively. you need to download the djvu reader to view the images. If you have trouble let me know.
#3

Thanks Bob,
I can make it with those very easily.
Thanks Again,
Scott




Users browsing this thread:
[-]
Recent Posts
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM

[-]
Who's Online
There are currently 2712 online users. [Complete List]
» 2 Member(s) | 2710 Guest(s)
AvatarAvatar

>