Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Looking for a needle for a Dynamic reproducer !
#1

My friend ask me to fix his 46-1209 Philco, the problem that I quickly ran into was the needle in the Dynamic Reproducer was broken, point missing ! The pick-up DOES make noise thru the radio , but the tone arm just floats across the record ! I have included a link to my "Photobucket" album, showing the correct needle #001 , the tone arm does NOT have any guard ,as shown in #02 , without the guard the needle would bend quickly(#02) ! Does anybody have ideas where I could find one or two(maybe a spare) of these phonograph needles, Philco part no. 35-2661 ?
Thanks, Lee Petrie , Joliet, IL. 815-744-1051
[Image: http://i404.photobucket.com/albums/pp122...661001.jpg]
[Image: http://i404.photobucket.com/albums/pp122...266102.jpg]

(edited by site admin to show pictures)
#2

Hi Lee

You might try West-Tech Services...I think Gib either has the correct replacement or a suitable substitute?

http://www.west-techservices.com/

--
Ron Ramirez
Ferdinand IN
#3

Hi Ron, Thanks for your suggestion of "Gib" at West-Tech, I just sent him an email/with pictures! Lee




Users browsing this thread:
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 2353 online users. [Complete List]
» 3 Member(s) | 2350 Guest(s)
AvatarAvatarAvatar

>