1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco Guy in Minneapolis-St Paul
satveerc
New Member
*
Posts: 2
Threads: 1
Joined: Nov 2016
City: Minneapolis, MN
#1

07-07-2020, 10:28 AM
Greetings, first time poster here. Are there any Philco repair people, or do you know of any Philco repair people, in the Minneapolis-St. Paul area? Would appreciate any references!
Find
RodB
Phorum Expert
*****
Posts: 1,135
Threads: 46
Joined: Feb 2015
City: Roseville, MN
#2

07-07-2020, 12:58 PM
Hi and welcome to the Phorum. I'm in Roseville, is that close enough for you? I noticed that the Phorum also has a new member from Eden Prairie who joined last week. There's also a couple old timers from the area. Get familiar with the site and ask how we can help.

Rod
Find
satveerc
New Member
*
Posts: 2
Threads: 1
Joined: Nov 2016
City: Minneapolis, MN
#3

07-07-2020, 12:59 PM
Roseville is great! Can you email me your contact info? satveerc@aol.com
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM
Philco model 38 code 121 not receiving signal.
Congrats on your success Stormlord. My rough guess is that since both the 15 and the 1A6 are supposed to be shielded, I...MrFixr55 — 10:04 PM

[-]
Who's Online
There are currently 722 online users. [Complete List]
» 2 Member(s) | 720 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration