Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1937 Coronado Model 650 Farm Radio
#31

I used a Meissner replacement 456 kHz Oscillator Coil. 

I just used a couple of 1.2v NiMH Rechargeable Batteries to power the filaments on this thing. I have a Radio Shack 2 D Cell battery clip that is wired up to a 1N4007 diode for voltage drop and I put my rechargeable D batteries in there.

I was actually able to get about 3 1/2 hours of play time out of the radio with that setup with plenty of juice to spare, and my D batteries weren't even fully charged! :^D
#32

My great grandad George was a farmer and he would have been proud to hear something like that working again Well done! Happy New Year.
#33

OK So a strange issue going on with my radio, it had been working like a champ for a week and a half but now all the sudden it refuses to power on, and no its not the batteries because I checked those and they were fine. 

I have a feeling its the power switch as it was kind of acting wonky when I first got this going where it would require being turned on and off a couple of times before it would finally power on.

Any ideas as to what the problem could be?

Thanks,

Levi
#34

You may have nailed it, power switch........does any current get into the circuit when switch open?

Paul

Tubetalk1
#35

If you are feeling lucky apply a small amount of WD40 to the switch and work it open and close a few times. let it sit for about a hour then power up your set. Good luck David
#36

Thanks, I'll give those things a try.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 2346 online users. [Complete List]
» 2 Member(s) | 2344 Guest(s)
AvatarAvatar

>