Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Clear Schematic for 41-255
#16

RossH -

Were you looking at our copy of the 1941 Yearbook, or one that you found elsewhere?

Dale H. Cook, GR/HP/Tek Collector, Roanoke/Lynchburg, VA
https://plymouthcolony.net/starcity/radios/
#17

Ross, sorry, clicked on the wrong one. here's the down load for the 41-255 as an attachment.


Attached Files
.pdf Part44-Philco 1941 RMS Year Book.pdf Size: 1.35 MB  Downloads: 110
#18

What's really funny is I looked at the pages and saw 255 and it took me 30 sec of looking at the schematic trying to figure out why it wasn't matching what I had before it dawned on me - I had transposed the numbers in my head.

This is perfect. Besides starting to work on one of these I am going to recreate this schematic from scratch. I've done a few ten others but this will be my first Philco recreation. I'll post when it's completed and gone over a few times. 

Thank you very much for your time and consideration in doing this, and a big thank you to all who chimed in.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.
#19

Hello Ross,
We have all been there don't worry the guys here have you taken care of !!
Sincerely Richard
#20

Hi Ross,
I don't know if you still need a clear schematic for the 41-255 but here is one that I cleaned up. I added pin numbers on the tubes and corrected 2 part #s (#29 and 33 were reversed on the schematic). Also, voltages are in dark red, and where provided, I color-coded the wire color name.
Fran


Attached Files
.pdf Schematic-pdf.pdf Size: 1.37 MB  Downloads: 117
#21

AH Just noticed 1 error on my cleaned-up schematic...
Part # 27 - the 8uf electrolytic cap...The lead that is marked RED should read GRN (green). Old eyes are not what they used to be!
Fran
#22

Thank you, Fran. I'll add it to the mix.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
The thrill is gone again, thought I was close to being done with it. Well Friday it was receiving broadcast, Saturday mo...osanders0311 — 07:47 PM
Help with Supreme 599
Iam getting closer to fixing it. I bumped Up the tranny voltage to get 5v on the 80 tube. I gan get the needle to move ...daveone23 — 03:41 PM
Philco 42-345 Restoration/Repair
Hello RodB, Checking my previous post I realized you're the one with the 42-340. I replaced the string for the tuning...osanders0311 — 03:12 PM
5U4 vs 5Z4 tubes
I saw no evidence of anything going wrong. The transformer is fused already which is nice. Interestingly the 5z4 did...bridkarl — 02:37 PM
5U4 vs 5Z4 tubes
I doubt anything cooked in 30 seconds because of the oops! These are very similar tubes, and nothing but transformer re...GarySP — 02:30 PM
Restoration of the Canadian General Electric A-87
Paul Philco322.You will be keeping very busy, you may have to go back to work for a breakIcon_smile. Paul To rel...RadioSvit — 01:57 PM
5U4 vs 5Z4 tubes
I grabbed the wrong tube and put in a 5U4 tube instead of the 5Z4 - I just had the rectifier in with no other tubes. Af...bridkarl — 01:54 PM
Restoration of the Canadian General Electric A-87
After applying the filler to the entire body, I noticed that the shades of the facade and the side and top walls were ve...RadioSvit — 01:49 PM
Restoration of the Canadian General Electric A-87
You will be keeping very busy, you may have to go back to work for a break:). PaulPaul Philco322 — 01:46 PM
Restoration of the Canadian General Electric A-87
After removing the control knobs, chassis, dynamics and scale frame, I first started restoring the torn piece of veneer....RadioSvit — 01:20 PM

[-]
Who's Online
There are currently no members online.

>