Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philcos from New Zealand and Peru
#1

The AM only Philco 401 is from New Zealand, and the multiband Philco is from Peru (at least that's where I got it from via ebay).

I could use a schematic for the 401 if anyone has one, thanks.


Attached Files Image(s)
   
#2

The New Zealand set looks like an Australian made Philco from the 1950s, note that it uses the same cabinet as a U.S/Canada Transitone model but with a glass dial. The set from Peru looks a lot like a member of the Philco Tropic series, which was an export model, it may have been assembled in Peru but it looks like it's patterned from a Tropic with the two short wave bands.
Regards
Arran
#3

Here's my 46-806:

[Image: http://www.philcoradio.com/gallery/image.../46806.jpg]

http://www.philcoradio.com/gallery/1946a.htm#q

Yep, it is a member of the Tropic series, most of which were made in Philadelphia and then exported, mostly to South America but to other countries as well. I've received emails from folks in places like South Africa and northern Europe who have Tropic sets.

It appears that sometime in the 1950s, Philco Tropic production switched to Philco's UK subsidiary. I have two UK-built Tropics; one was purchased from a USA seller but I had the other one sent here from England; the radio was very cheap but the shipping wasn't! Icon_eek

--
Ron Ramirez
Ferdinand IN
#4

Ron;
Didn't they produce a number of Tropic models in Canada as well, I remember that you posted some pictures of an early 50's example with a broken cabinet, with a hot chassis, and it was made in Canada. There is a 1950s era Philco Tropic about three hours South of me but the party selling it wants $65 for it, they claim that it was from the Caribbean in the ad. I thought about asking about it but it's still just a plastic/Bakelite set for too much money.
Regards
Arran
#5

Yes, you're right, Arran. That early 1950s Tropic I have - a model 3010 - is rubber-stamped on the back of the chassis MADE IN CANADA. And, yes, it is a hot chassis. Icon_eek I bought a 51-532 just for the cabinet, to replace the broken but otherwise identical 3010 cabinet.

The Tropic you mention for sale was, I am sure, exported to the Caribbean when it was new but it was most likely not manufactured there.

Speaking of Canadian sets, there are a few Philcos that were made and sold in Canada that are identical to Tropic sets built in the USA and exported south. Sets such as the 35AT (41-712T), 39AT (41-722T), and the 55AT (42-760T). In fact I have a 39AT, I consider it part of my Tropic collection since it is identical to the 41-722T. I used to own a 55AT but later sold it.

--
Ron Ramirez
Ferdinand IN
#6

Ron;
On the 46-806 Tropic model that you show where is the range switch located? I see two knobs on the front like a normal Transitone with the same cabinet but no third one, on most small sets like that they would have drilled a third hole in the front and added the range switch there.
Regards
Arran
#7

They put the band selector switch on the back of the radio. Mounted to the back side of the chassis. Philco must have expected that few users of this set would change bands all that often...




Users browsing this thread:
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently no members online.

>