Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-190 bezel color question
#1

So I'm cleaning a lifetime of dirt off of the metal bezel with some green cleaner and while dirt is coming off, I'm left with areas that look like something ran down the bezel. So I try some alcohol and quickly realize that I'm removing the gold paint on the bezel. That's OK because I couldn't have put it on the radio looking like it did. So has anyone spray painted one of these bezels? I would describe it as a mat light gold color. Just go to Lowes and see what I can find?
#2

I found a thread answering this question.
#3

Although the paint recommended in that thread, Valspar Plasticote, was not available locally. So I picked up Valspar Brilliant Gold 66009 at Lowes. First coat was too thick and I got some noticeable orange peel. Quickly removed that with some alcohol and did 2 thin coats. I'm 100% satisfied.

With flash:
[Image: http://i191.photobucket.com/albums/z309/...file-8.jpg]

w/o flash:
[Image: http://i191.photobucket.com/albums/z309/...file-7.jpg]
#4

Hum. Mine isn't gold it is a nickle (plated?) color. I have had that radio for 30 years, so it is hard to remember, but I think it has always been that color.
#5

Quote:it is a nickle (plated?) color

Yes, it may be that color. Not plated, though, because alcohol takes it off easily. Like this?:

http://www.radioatticarchives.com/radio.htm?radio=2034

This one may be repainted; it's very close to mine now:

http://www.radioatticarchives.com/radio.htm?radio=2036
#6

When I stripped all the sexy gloss black off my escutcheon, I found traces of the original color underneath. I'd say yours is definitely in the right area. And funny you should mention, I think I bought the last can of the closest-thing-to on the west coast... I haven't seen it anywhere since.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2217 online users. [Complete List]
» 2 Member(s) | 2215 Guest(s)
AvatarAvatar

>