1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 201X - Name plate in radio???
cwysong
Junior Member
**
Posts: 26
Threads: 6
Joined: Jan 2011
City: Bothell, WA
#1

06-15-2013, 10:38 PM
I just finished stripping down a Philco 201X. It had lacquer on the inside as well as the outside. One thing I found when I cleaned the chassis board is an oval brass plate with the name of Powers on it. It is nailed in.
Did these radios get the name of the person who assembled the radio, or could this have been added after?
This radio has not been touched. The electronics are all original, and there was enough dust on it to make me think the insides have never been moved.
Has anyone seen this before?
Let me know.
Thanks
Chris

   
Find
Arran
Phorum Expert
*****
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#2

06-16-2013, 01:42 AM
Maybe the brass tag was put in there by a dealer? I have an RCA console where the dealer added their decal to the dial bezel.
Regards
Arran
Find
cwysong
Junior Member
**
Posts: 26
Threads: 6
Joined: Jan 2011
City: Bothell, WA
#3

06-16-2013, 08:00 PM
Aaron, I hadn't thought about that. I'll be the dealer put it on. For $250, this was a very expensive radio!
Thanks
Chris
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2041 online users. [Complete List]
» 1 Member(s) | 2040 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration