Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70 1929 Cabinet
#1

I am trying to "restore" my philco lowboy cabinet; it is really dry mahogany and I did not know if I should just use an oil on it or what .
Any suggestions?


Attached Files Image(s)
   
#2

Hi George and welcome to the phourm!
Just to be clear on your set it isn't a model 70 as it didn't come out till 1931. It's probably a model 87 or 95 but would have to see the back of the set to tell which one it is. I don't know if you know it or not but the legs on your cabinet have been removed. It should stand a bit taller. Here's a pic of it: http://www.philcoradio.com/gallery/1929c.htm#d
I have a model 87 and the 95 both are good set for 1929 technology!
GL
Terry
#3

I like to use GoJo pumice free hand cleaner to get all the old oil and wax off first. Then, Howard's Restore-a-Finish it it needs a little color. Finally, Howard's Feed'n Wax (orange oil + beeswax).

Here's a Philco 70 lowboy from 1931 for comparison.
[Image: http://farm3.staticflickr.com/2181/41215...db21_z.jpg]
#4

Thanks everyone! I will try the products you recommend for the finish. I am also trying to find a set of legs for my radio since they have been removed.
George




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently no members online.

>