Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

antenna
#1

hi guys
here is my problem
I live in condo bottom floor. next to train tracks and local fm radio tower. have wr6 connected ground to water pipe ran 50 foot wire out door on ground radio barely picks up am volume very low hums,pops,motor boats but 10 min down road in metal garage short ground wire to electric box and 5 foot cable picks lot of stations ( God and Spanish Icon_sad )sounds great and had volume I tried radiola18 same thing what can I do for better antenna ? solid cable or strand cable ? better to ground to water or electric ? Icon_crazy
thanks sam
#2

Has the set been serviced?? Sound more like radio problem than an antenna. Set shouldn't be motorboating and the like if it working properly.
Terry
#3

Could be interference in the condo too. Wall warts are notorious for causing radio noise. Try plugging into a different socket.

The artist formerly known as Puhpow! 8)
#4

hi guys
terry radios were serviced both sound same in house but if I take to work and use they sound great no static between stations lots volume and stations. thinking about running wire up to roof like you said but 3 stories and no ladder
puhpow only has 3 circuits for entire house. tried same thing. I know walls and ceiling have metal slats in them as older houses had wood. and all the fm radios I have had would only pick up local bleeding talk radio 101.5 and all most no other stations
sam
#5

If you can get to the roof and make an antenna there, and run a coax downlead without disturbing anyone you would be fine.




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 1742 online users. [Complete List]
» 2 Member(s) | 1740 Guest(s)
AvatarAvatar

>