Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Phono Cartridge
#1

I have a 46-1256 radio phono and the phone only lets out a small
sound from the needle/cartridge but not from the speaker. The radio plays great through the speaker. Is the cartridge bad? if so where can I find a cartridge for a Philco radio/phonograph model 46-1256
#2

Welcome to the Phorum!

If it's a table model radio / phono combo, are you sure you don't mean model 48-1256? There wasn't a 46-1256. There was a 46-1226 console radio / phono. The first two digits of your model number indicate the year of manufacture of your set.

At any rate, regardless of which model you have, more than likely the cartridge is bad. You may be able to find a suitable replacement here: http://www.thevoiceofmusic.com/

Or, you may be able to have your cartridge rebuilt here:
http://www.west-techservices.com/

Greg V.
West Bend, WI
Member WARCI.org
#3

Greg, Thanks for the reply,you are right the unit is a 46-1256. West-techservices would be the best bet,they are closed till 5/5/2014 due to moving.
#4

Be sure to mention to West Tech the phono
changer is a Philco Model D-10.

Chuck
#5

Thanks Chuck




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 2396 online users. [Complete List]
» 3 Member(s) | 2393 Guest(s)
AvatarAvatarAvatar

>