Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Atwater Kent 206
#1

Just need an opinion- to strip or leave it be. Stripping is not that difficult thing to do, just wonder if it still looks presentable.
Some like it that way, "patina" and all, not sure. Thanks.

[Image: http://i881.photobucket.com/albums/ac17/...172154.jpg]
#2

My opinion:

[Video: http://www.youtube.com/watch?v=Ho02oKHuveY]

--
Ron Ramirez
Ferdinand IN
#3

Only 1 picture, but, from that, I would 'let it be" too.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

I would also leave it as is. The finish is original only once, and for 80 years old it looks very nice. 
#5

I agree with everyone else..... leave it alone. The most I would do is a Go-Jo cleaning, some Howard's or Old English, and some quality paste wax.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

It's a good looking cabinet. Paul said it best Icon_smile
#7

We have consensus by mavens..Needless to say, will comply.
Thanks guys.
#8

  I would have to see more pictures, with sharp focus, brighter lighting, and not at odd angles, sometimes they make things look better then they really are in person. A case in point was the Rogers Ten-60 I got from a guy selling it over craigslist, in a front on view it looked pretty nice, when I went to look at it in person I realized that someone had rubbed it down with Howard or some other scratch hiding product. Now obviously this set is not being pedaled on craigslist but a rub down with Gojo can have much the same effect, until the remnants of the Gojo evaporates.
Regards
Arran
#9

I wouldn't strip that. You can always touch the small worn areas up. If you use Howards you can touch up or go over it at any time with Laquer based products.
#10

(11-03-2014, 01:39 AM)Arran Wrote:    I would have to see more pictures, with sharp focus, brighter lighting,  remnants of the Gojo evaporates.
Regards
Arran

Your wish is my command.. Here it is, w/o GoJo:[Image: http://i881.photobucket.com/albums/ac17/...df5fda.jpg]
[Image: http://i881.photobucket.com/albums/ac17/...6fdca8.jpg]

[Image: http://i881.photobucket.com/albums/ac17/...9b882b.jpg]
Keeping the cabinet original, I did not want to have the chassis look brand new, just clean.
[Image: http://i881.photobucket.com/albums/ac17/...875acb.jpg]
[Image: http://i881.photobucket.com/albums/ac17/...ba0ff5.jpg]




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently no members online.

>