Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Remler wood console
#1

   

I found this on craigslist for $80. I can't seem to find any info on Remler wood consoles. I found lots of stuff about their table bakelite units. Anybody have any info about this? And maybe if it's a good buy?

Thanks,

Pat
#2

If it is clean inside...maybe. Provided the speaker is good.
#3

Looks like it might be an amputee though...

No matter where you go, there you are.
#4

It has a short.............................cabinet.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#5

(11-08-2014, 09:21 PM)Phlogiston Wrote:  It has a short.............................cabinet.

So do I. But I think I'll pass. Thanks to you all.
#6

  Given the weekend warrior refinish, the missing legs, broken escutcheon, broken speaker grille, mystery knobs, $80 is way to much, maybe $30-40 tops, if it had everything still in the back, but preferably less. As I keep explaining to people, it's the restoration costs in time and money that nails you, sometimes even if the radio is free it's too much.
Regards
Arran
#7

(11-09-2014, 03:11 AM)Arran Wrote:    Given the weekend warrior refinish, the missing legs, broken escutcheon, broken speaker grille, mystery knobs, $80 is way to much, maybe $30-40 tops, if it had everything still in the back, but preferably less. As I keep explaining to people, it's the restoration costs in time and money that nails you, sometimes even if the radio is free it's too much.
Regards
Arran

I agree 100%. My time isn't worth much because it's a hobby, and caps and resistors are cheap, but the rest can cost an arm and a leg, and you'll never be able to sell it for more than you have invested. I used to restore classic cars as a hobby, and if you weren't careful, you could put $25,000 into a car, and only sell it for $20,000. At least with this hobby, my bank account doesn't suffer as much, and my wife lets me sleep in the bedroom rather than the garage.




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM

[-]
Who's Online
There are currently 1434 online users. [Complete List]
» 3 Member(s) | 1431 Guest(s)
AvatarAvatarAvatar

>