Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

620 cabinet logo misplaced?
#1

hello:
we have a curious 620 cabinet, as the philco logo is set between the knobs and dial. not at the top like all of the pictures iv'e seen online.
the sticker inside of it says run #1
is this possibly a rarity? or could it be a misplaced decal from a restoration?
anyway to tell, or any info would be appreciated.
thank you.
   
   
#2

Neat! Icon_thumbup

That's an original decal. You can tell the difference between it and the Radio Daze PH8 by the fact that the 1932-36 originals had more of a copper color rather than gold.

I seem to recall that Philco's photos of this model show the decal as on your cabinet. I suspect that the very first 620B cabinets to be built had the decal placed there, before Philco decided to move the decal to the top edge as seen on most 620B cabinets.

As we all know, Philco was famous (infamous?) for their running changes in models. So it should not be surprising that those changes would extend to decal placement on cabinets as well.

--
Ron Ramirez
Ferdinand IN
#3

(01-03-2015, 10:01 PM)Ron Ramirez Wrote:  Neat! Icon_thumbup

That's an original decal. You can tell the difference between it and the Radio Daze PH8 by the fact that the 1932-36 originals had more of a copper color rather than gold.

I seem to recall that Philco's photos of this model show the decal as on your cabinet. I suspect that the very first 620B cabinets to be built had the decal placed there, before Philco decided to move the decal to the top edge as seen on most 620B cabinets.

As we all know, Philco was famous (infamous?) for their running changes in models. So it should not be surprising that those changes would extend to decal placement on cabinets as well.


Thanks for looking at it ron.
We will take care of it.

Icon_smile




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1863 online users. [Complete List]
» 1 Member(s) | 1862 Guest(s)
Avatar

>