1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco model 19B I.F.
VE6ZRT
Junior Member
**
Posts: 5
Threads: 1
Joined: Feb 2015
City: Calgary, Alberta Canada
#1

02-28-2015, 04:36 PM
I have just restored a Philco chassis 319 ( Made in Canada version of 19/89 ) and am about to do an alignment on it.

I am confused since the I.F. frequency is indicated as 260KHz or 460KHz depending on what document you are using…

Can anyone provide a definitive answer on the I.F. frequency of the 319 chassis which was used in the model 19 series in Canada? I am going to guess 460KHz for now…it would be obvious I assume once I start the procedure…
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

02-28-2015, 07:31 PM
Nope, the proper IF frequency for model 319 is the same as the USA model 19 - 260 kc.

(I checked the RCC data to be sure.)
--
Ron Ramirez
Ferdinand IN
Find
VE6ZRT
Junior Member
**
Posts: 5
Threads: 1
Joined: Feb 2015
City: Calgary, Alberta Canada
#3

03-02-2015, 09:22 AM
(02-28-2015, 07:31 PM)Ron Ramirez Wrote:  Nope, the proper IF frequency for model 319 is the same as the USA model 19 - 260 kc.

(I checked the RCC data to be sure.)

Thanks for the clarification Ron.  By the way this chassis works quite well even without an alignment...even the shadow meter still functions!  What I have also noticed is that the sound quality with the lowboy/console 10 inch speaker is quite good and there is basically no sign of 60/120HZ hum...very nice radio to listen to.

Thanks.

PH
Find
klondike98
Phorum Moderator
******
Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

03-02-2015, 10:10 AM
Welcome to the Phorum!!!
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
VE6ZRT
Junior Member
**
Posts: 5
Threads: 1
Joined: Feb 2015
City: Calgary, Alberta Canada
#5

03-02-2015, 04:10 PM
(03-02-2015, 10:10 AM)klondike98 Wrote:  Welcome to the Phorum!!!

Thanks Bob...I have one more Philco to restore ( a floor model from 1939...)...might get to it in the fall...

PH
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2318 online users. [Complete List]
» 2 Member(s) | 2316 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration