Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16-B chassis finito!
#1

check this out!!

[Image: http://i225.photobucket.com/albums/dd32/...safter.jpg]

Steve McDonald
#2

You're kidding...right?

--
Ron Ramirez
Ferdinand IN
#3

LOLOL!!! Yes, that picture IS a put-on. I just couldn't resist! That's a gag shot! I took it as a spoof for a friend on Cape Cod.
Actually that is a picture of a blown-up mobo out of my Super-Duper V-31 computer poised to look like the real chassis work. That would be a TRAVESTY to actually do that to a good old Philco.
The REAL chassis doesn't look too much different than it did when I started it.
I do have the speaker problem, though.
All four connections to the speaker are shorted together! Any help will be worhipped from me!

Steve McDonald
#4

That's one way to get the Green Hornet on your antique radio.

Harv

Harv
#5

You ROCK Tube!! ..... Great photo indeed! How is the SW reception on that set? Looks like perhaps someone forgot to "update" the bias-resistor in that restoration by looking at the photo?? (hee hee), that photo should give a few purists-to-originality here a mere case of the red-azz?!! rotflmao!! Icon_wink
#6

Ron didn't sound too happy about it, now DID he?? Icon_lol I'm just a subversive and muckraker at heart!
BTW, the REAL resto doesn't look too much different than my before picture. I wanted to use Orange Drops for this re-cap, but you all KNOW THEY won't fit inside one of those Philco Tar-Boats!!
The filters are down in there now, because I wanted the top end to look original!
But only those and a couple more new caps ( li'l bitty yellow thangs) show...one to the volume, etc.
Thankfully, the top of the chassis was just dirty!

If I can sort out the speaker problem, it's good to go. The input choke/output trans is shorted together. Icon_evil

Steve McDonald




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 369 online users. [Complete List]
» 2 Member(s) | 367 Guest(s)
AvatarAvatar

>