Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
Hi All,
New member- first time poster.
I have a model 81 that I have rebuilt. Replaced all caps, resistors and rewound the ant coil (primary side).
The speaker cone is in bad shape but it plays.
The set is working and I can get a local station in my basement- so I am not too far from finished.
I have been making voltage measurements on the tubes to confirm everything is in spec and I am having a problem reconciling the 42 output tube with the rider voltage chart for this radio. Specifically, the control grid CG to cathode K. The rider manual calls for 2.3 V. The 42 tube data sheet calls for a control grid voltage of -16.5 to -20 v. I am measuring about -17 v from CG to K (ground). Not sure if I have a problem or not.
My plate, screen and filament voltages are in spec. (riders chart).
thanks for the help,
Anthony
Posts: 670
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
I say ,,,you are in the range between -16.5 to -20,,,sounds good to me
Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Welcome to the Phorum!
If its playing well the voltage reading seems good to me. An alignment might be helpful as well.
Posts: 4,441
Threads: 419
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
Anthony, you live in the same town as one of our members, Morzh! Good luck and welcome to the land of Philco.
paul
Tubetalk1
Posts: 16,506
Threads: 572
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Tony
Where in Jackson are you?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 4,892
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Perhaps it was an error? The control grid voltage should never be positive on any audio output tube that I know of, maybe it was supposed to be -23 volts rather then 2.3 volts? If it was actually 2.3 volts the output would sound like garbage if it worked at all.
Regards
Arran
Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
(01-20-2016, 10:56 PM)morzh Wrote: Tony
Where in Jackson are you?
Hi Morzh,
I am on Autumn Avenue, between Diamond and Cobain roads. About 3 minutes from the Justice complex.
Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
Thanks for the help!
It does need an alignment (IF and the dial). Unfortunetly, the dial is brittle and in alot of little pieces. I ordered a replica replacement. When that comes in I should be able to do the dial and other alignments.
Yes, I'm in Jackson- near diamond road about 3 minutes form the Justice complex.
Also, I used to attend the NJARC meetings in Freehold with my grandfather until they moved to Princeton and Wall.
thanks again,
Anthony
Posts: 16,506
Threads: 572
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Not too far, 6 minutes maybe. I am in a development by St Aloisius church, on Bennets Mills.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 4
Threads: 1
Joined: Jan 2016
City: Jackson NJ USA
(01-21-2016, 08:46 PM)morzh Wrote: Not too far, 6 minutes maybe. I am in a development by St Aloisius church, on Bennets Mills.
Yes, I know that area. My Kids went to St. Al's.
-Anthony
Users browsing this thread:
|
|
Recent Posts
|
|
Philco model 38 code 121 not receiving signal.
|
| Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM |
|
Testing a speaker and output transformer Trutone A2-G
|
| morzh
Short-circuited turns can be considered as a half-dead transformer.
But on this case transformer will hot and s...Vlad95 — 11:01 AM |
|
Testing a speaker and output transformer Trutone A2-G
|
| I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM |
|
Philco model 38 code 121 not receiving signal.
|
| Good news everyone! I think I have found everything I need for rewinding the antenna coil primary.
I found some pla...Stormlord5500 — 09:40 AM |
|
Philco Battery-WWII vintage
|
| My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM |
|
Philco Battery-WWII vintage
|
| Hello Bob,
What Amazing find!
Sincerely Richardradiorich — 10:19 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| Hi Murf,
Do this:
Monitor between ground and one plate of the rectifier while playing the radio. Do the same with ...MrFixr55 — 09:51 PM |
|
Philco Battery-WWII vintage
|
| Mike;
I take it that Soviet cars did not come equipped with block heaters, hence the hot oil change? Where I lived in...Arran — 08:42 PM |
|
Philco 42-345 Restoration/Repair
|
| The more the better. (Within reasonable limits.)
2-5 times more is no problem in this case.Vlad95 — 03:50 PM |
|
Philco 42-345 Restoration/Repair
|
| Thanks, RodB and Vlad95,
I was mainly trying to figure out this capacitor to locate a replacement, Vlad thank you for...osanders0311 — 03:44 PM |
|
Who's Online
|
There are currently 978 online users. [Complete List]
» 2 Member(s) | 976 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
