Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 46-1201 really it followed me home!
#1

Yup, any more Philcos and I'll have to find a dealer sign to hang on my front door!
Again as in my other finds it is unmolested and original. Wait a minute, the power cord has been patched.
Glad I retired to a life of leisure Icon_lol to a hobby of restoring old radios.
#2

Those are cool little players! My wife has a photo of her grandmother sitting next to one. I'd like to get one someday but I'll wait for the right deal.
#3

They are quite heavy to ship. Figure around $40 at a minimum, which can add a lot to the final cost if you go the eBay route to find one (and there are always examples on there available). There's one on there right now with a BIN for $29.95...with $49 shipping. I'm NOT advertising it, just citing it as an example of how shipping on one of these can cost almost twice as much as the radio itself!

Greg V.
West Bend, WI
Member WARCI.org
#4

Isn't it funny that the cost of fuel has gone down quite a bit, yet the cost of shipping keeps going up? Icon_thumbdown

--
Ron Ramirez
Ferdinand IN
#5

Very true, Ron. I sent a media DVD...in a paper sleeve and bubble wrap envelope...to a friend in the UK a few weeks ago. It weighed practically nothing, and I used to be able to send these to him for only a few dollars using small packet rate. The cheapest rate now was $13!!

Getting back to the 1201's, I once found one in pretty rough shape on eBay for $10 or best offer. Shipping was $20 (at the time). I offered the seller $1.00 for the set and they accepted. It was the "somewhat" harder to find 48-1201 (9 times out of 10 you're going to find a 46-1201 because there were SO many more produced under that model number during 1946-47).

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM

[-]
Who's Online
There are currently 863 online users. [Complete List]
» 2 Member(s) | 861 Guest(s)
AvatarAvatar

>