Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE F-96 wood repair
#1

I'm working on a F-96 and it has a chunk taken out of it.


[Image: http://i.imgur.com/4fmxl9r.jpg]
Anyone have a better sense of wood identification than me? I'm going to try a veneer patch, but I suppose I better know what wood I'm looking for.
#2

Has the side pulled away for the top?? The contour of the side doesn't look like it matches the top. Are you thinking of refinishing the whole cabinet or just repairing this issues?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I am not an expert, but that looks like mahogany, AKA luan plywood.
#4

Im refinishing it completely. I've reglued the loose edge to the top. I've stripped and sanded. I have some veneer samples coming.

I'm not sure how to approach the missing substrate issue.
#5

(08-10-2016, 08:05 PM)kc5gym Wrote:  I am not an expert, but that looks like mahogany, AKA luan plywood.

No, It's not Luan plywood, it's one of the mahogany look a likes, sapele. or possibly quartersawn makore. G.E listed what sort of veneers they used in their advertising and I think that they liked to use one of those veneers, particularly of the ribbon striped variety, on their cabinets in the 1938 and 39 model years.
 
http://www.wood-database.com/lumber-iden...ds/makore/

http://www.wood-database.com/lumber-iden...ds/sapele/

Regards
Arran
#6

(08-12-2016, 03:38 AM)Arran Wrote:  
(08-10-2016, 08:05 PM)kc5gym Wrote:  I am not an expert, but that looks like mahogany, AKA luan plywood.

No, It's not Luan plywood, it's one of the mahogany look a likes, sapele. or possibly quartersawn makore. G.E listed what sort of veneers they used in their advertising and I think that they liked to use one of those veneers, particularly of the ribbon striped variety, on their cabinets in the 1938 and 39 model years.
 
http://www.wood-database.com/lumber-iden...ds/makore/

http://www.wood-database.com/lumber-iden...ds/sapele/

Regards
Arran

That Makore looks like a possibility.
#7

(08-12-2016, 07:40 AM)Tgace459 Wrote:  
(08-12-2016, 03:38 AM)Arran Wrote:  
(08-10-2016, 08:05 PM)kc5gym Wrote:  I am not an expert, but that looks like mahogany, AKA luan plywood.

No, It's not Luan plywood, it's one of the mahogany look a likes, sapele. or possibly quartersawn makore. G.E listed what sort of veneers they used in their advertising and I think that they liked to use one of those veneers, particularly of the ribbon striped variety, on their cabinets in the 1938 and 39 model years.
 
http://www.wood-database.com/lumber-iden...ds/makore/

http://www.wood-database.com/lumber-iden...ds/sapele/

Regards
Arran

That Makore looks like a possibility.

 Better strip some of the original finish off, just to make sure, G.E was like many manufacturers in that their cabinets had a tinted finish over everything to even out the variations in wood grain.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM

[-]
Who's Online
There are currently 1158 online users. [Complete List]
» 2 Member(s) | 1156 Guest(s)
AvatarAvatar

>