Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

NOOB here- how to set push buttons on model 39-45
#1

Hi everyone,  thanks for letting me join this site . When I was growing up in the 1950's my parents had a model 39-45 we listened to every day. Now here I am 65 years later and have finally finished its restoration. I'm trying to figure out how you set the push buttons. Does it require changes in the chassis or is there a way for the user to set them?  Also,  can I post a picture here?

Thanks,
Warren
#2

Hi and welcome,
The info the here in the service manual: http://www.nostalgiaair.org/Resources/298/M0013298.htm
There are two adjustments for each push button. One sets the osc and the other adjusts the ant circuit.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Welcome to the Phorum!

Yes you can post photos. See:
https://philcoradio.com/phorum/showthread.php?tid=29
#4

Welcome to the phorum!  Lots of very helpful pholks here to assist any way they can.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#5

Anyone know how or where to get new station labels?
#6

https://philcoradio.com/phorum/showthread.php?tid=5148

--
Ron Ramirez
Ferdinand IN




Users browsing this thread:
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... The console body has been restored, while the varnish dries reliably I started repairing the chassis.. Of ...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently 986 online users. [Complete List]
» 1 Member(s) | 985 Guest(s)
Avatar

>