Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 questions
#1

Is there a service bulletin noting the circuit differences between the model that uses the 6A5G vs the 6B4. Is that model distinguish by a code number other than 121 or 122?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

Terry,

It says the changes are in Philco 8-3.
I haven't seen anything there specifically about 37-116.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

I know we had discussed it a little ways back when you got
your set.
Looked up the pin out and kinda interesting as the cathode is
internally connected filament at it's mid point. I would have
thought that it would have a separate pin with no relation to
the filament. Does your set have have a filament balancing
or hum adjusting pot?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Terry,

Don't want to misinform you, I do not remember. There might have been no trimpots in mine. Mine is 6A5 version.

Now that I think about it, probably there were no trimpots.

the two spare chassis' I have are 6B4 types. Probably same as yours.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

Terry

here.
https://philcoradio.com/phorum/showthrea...ght=37-116

My old thread.

Look at the comment #47 by JohnR.

This has both Service Bulletin # and the pot (#128) removed.
I guess it is a dual pot, as both pots have the same number.

Funny...in the mentioned SB #258 I found nothing about codes 125/126.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

Tnx Mike,
I thought that was the case but wanted to be sure.
There's a poster on arf that was asking abt the differences.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM
Philco model 38 code 121 not receiving signal.
Congrats on your success Stormlord. My rough guess is that since both the 15 and the 1A6 are supposed to be shielded, I...MrFixr55 — 10:04 PM
The list of my radio & TV collection!
A little light Saturday positive about our hobby in our feed... My new every Saturday video about antique radio equipme...RadioSvit — 02:12 PM

[-]
Who's Online
There are currently 782 online users. [Complete List]
» 2 Member(s) | 780 Guest(s)
AvatarAvatar

>