Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Last Philco tube radio
#1

Anyone know when the last tube radio came off the assembly line? 
What year and what is the model #?

Inquiring mind wants to know.

Thanks
Chris
#2

Sounds like you want to buy oneIcon_smile.

Paul

Tubetalk1
#3

I think you'll have to dig deep to find that information...

If you are asking for a purely tube radio, I suspect sometime around 1960-61 would be a good place to search. But many manufacturers used tubes up into the late 60's on their higher end radio/stereo offerings, usually in a hybrid combination of tubes and transistors.
#4

Looking at Beitmans for 1967-69 no tube sets for 1966 yes. On page 96 list these models P720, 721, 722, 723, 724, 880, 881, 882, 883, 884, 885. All AA5 sets. On Page 97 Models P710, 933, 941 all AM/FM.
#5

I have a Philco clock radio from approximately 1967-68, according to the date codes on the parts, they carried on a bit longer because most transistor sets required a power transformer, other then the hot chassis radios RCA put out.
Regards
Arran




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1884 online users. [Complete List]
» 3 Member(s) | 1881 Guest(s)
AvatarAvatarAvatar

>