1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Johnson's Paste Wax and a lot of elbow grease!
Cliff Byers
Junior Member
**
Posts: 18
Threads: 3
Joined: Jul 2019
City: Sheridan State, Province, Country: WY
#1

01-27-2021, 04:20 PM
Hello folks!

I'm showing an old Philco 41-255 all original finish with seven coats of Johnson's Paste wax.  Hand-buffed.  The old gal sits in pride of place of my living room for everyone to see.  She works excellently as well.


Attached Files Image(s)
   
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#2

01-27-2021, 05:34 PM
Harlow would be proud!
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Cliff Byers
Junior Member
**
Posts: 18
Threads: 3
Joined: Jul 2019
City: Sheridan State, Province, Country: WY
#3

01-27-2021, 06:12 PM
Thanks!
Find
klondike98
Phorum Moderator
******
Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

01-27-2021, 06:51 PM
Nice! Icon_clap Icon_clap Icon_clap
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
WyTex
Senior Member
****
Posts: 289
Threads: 42
Joined: Jan 2014
City: Jeffersonville State, Province, Country: PA
#5

01-27-2021, 06:53 PM
Fibber McGee and Molly time!
Find
NostalgiaRadioTime
Super Moderator
******
Posts: 1,531
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
#6

01-27-2021, 07:39 PM
An original circa 1946 can of Johnson's Glo-Coat. Mainly for floors but hey I bet some folks tried the stuff on their radio cabinets too! Icon_lol

   
Greg V.
West Bend, WI
Member WARCI.org
Website Find
Paul Philco322
Super Moderator
******
Posts: 4,442
Threads: 419
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#7

01-27-2021, 08:39 PM
I love just the heads, see that a lot in old ads. Thanks for posting.

Paul
Tubetalk1
Website Find
Cliff Byers
Junior Member
**
Posts: 18
Threads: 3
Joined: Jul 2019
City: Sheridan State, Province, Country: WY
#8

01-27-2021, 11:41 PM
I like this!!!  COOL!!
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1929 online users. [Complete List]
» 3 Member(s) | 1926 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios