1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
41-605 Squeal/Motorboat
glwells
Junior Member
**
Posts: 15
Threads: 5
Joined: Aug 2009
City: Columbus State, Province, Country: NC
#1

10-28-2021, 08:17 PM
I'm working on a 41-605, replaced the obligatory caps as well as some dominos, out of spec resistors, checked tubes, general socket and pot cleanups, etc. The AM side plays fine up to about 1400 where the oscillator starts the infamous squeal and motorboating right up thru the top of the dial. All good below 1400. The SW side works fine with no issues. I have it isolated to most likely issues with the oscillator circuit. A NOS 14AF7/XXD didn't help. Resistance specs of the oscillator coil are good. I've maneuvered lead and component placement as much as I dare in the oscillator area around the XXD. Oscillator padder 17A does impact the intensity but doesn't eliminate it. Can anyone offer any suggestions or hints as to what I may have missed?

Much appreciated.

Gary
WB9AYD
Website Find
vinzer
Member
***
Posts: 214
Threads: 16
Joined: May 2010
City: Kokomo, IN
#2

10-29-2021, 11:31 AM
Are all tube shields on?
Find
glwells
Junior Member
**
Posts: 15
Threads: 5
Joined: Aug 2009
City: Columbus State, Province, Country: NC
#3

10-29-2021, 12:12 PM
These are Loctals and I cleaned all of the tubes and sockets.
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration