1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 84 caps
Jimradio
Member
***
Posts: 201
Threads: 35
Joined: Jul 2016
City: Spring Lake MI
#1

01-03-2022, 01:07 PM
Restoring Philco 84 the Bakelite cap # 28 has 2 .015 caps, can I get by with .01Y or .05Y caps I don't have any .015 unless I order them.
Thanks.
Jim
Spring Lake MI
Find
morzh
Odobenus rosmarus
******
Posts: 16,508
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#2

01-03-2022, 01:10 PM
If those are the AC input filters, yes, 0.01uF is what you need, Y-rated.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Jimradio
Member
***
Posts: 201
Threads: 35
Joined: Jul 2016
City: Spring Lake MI
#3

01-03-2022, 05:44 PM
Thanks, Morzh
Jim
Spring Lake MI
Find
Jimradio
Member
***
Posts: 201
Threads: 35
Joined: Jul 2016
City: Spring Lake MI
#4

01-07-2022, 08:17 AM
Is there a later schematic not showing Cap. #32. I must have a later chassis it does not have cap. #32
Philco 84.
Thanks.
Jim
Spring Lake MI
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#5

01-07-2022, 11:31 AM
Just pretend it's not there. It's was to tune the field coil. What I do when I overhaul is replace 29 w/2x 10mfd@450v and 28 w/10mfd@35v. The 35v one goes w/the +side to the chassis and - to the hv c tap.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 01-07-2022, 11:32 AM by Radioroslyn.)
Find
Jimradio
Member
***
Posts: 201
Threads: 35
Joined: Jul 2016
City: Spring Lake MI
#6

01-13-2022, 08:00 AM
This radio is now completed, very nice radio but a little different than others I have restored.
Jim
Spring Lake MI
Find
Jimradio
Member
***
Posts: 201
Threads: 35
Joined: Jul 2016
City: Spring Lake MI
#7

01-14-2022, 07:49 AM
    This is the completed radio pic.
Jim
Spring Lake MI
Find
Paul Philco322
Super Moderator
******
Posts: 4,442
Threads: 419
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#8

01-14-2022, 08:06 AM
Real nice jobIcon_smile.

Paul
Tubetalk1
Website Find
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#9

01-14-2022, 05:08 PM
Has a nice original patina.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM

[-]
Who's Online
There are currently 2769 online users. [Complete List]
» 3 Member(s) | 2766 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration