Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 118X cabinet
#1

Seems I have a variation of the 118X cabinet that I have never seen before.  All of the Photos I have seen are slightly different on the top end of the cabinet.  Seems like this may have been a change between earlier to late versions of this cabinet.  Does anyone     have any InSite?

Thanks

Sam

Philco's: 86 Lowboy 90 Highboy 95 Highboy 76 Highboy 112X Console 118X Console 41-265 Console 41-608P Console 52GC 370 LZ 512 20 Baby Grand 70 Baby Grand 71B 52B 118B 60B 84B 610B 37-89B 38-10T 38-35B 41-221CI 42-321T 46-1203 48-214 48-206 49-506
#2

It seems I've seen a photo of that cabinet variation before.

Is this a Canadian version (3118X)?

If not, then it must be a factory variant.

Some Philco cabinets were produced by more than one furniture maker. It could be that Philco changed the design during production, or else one of the third party cabinet makers changed the specs on their own and produced this variant. We can't know for sure since everyone involved with production of these cabinets are all now deceased.

When I get a chance, I'll look in Furniture History and see if more than one company produced this "X" cabinet.

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron, I appreciate your in sight. There is a picture of the Canadian 3118X on page 57 of your
Philco book. it is not the same. On page 48 it gets closer on the top decorative area in front for the model 18X but then the bottom is different. Maybe just a factory or third party change up.

Philco's: 86 Lowboy 90 Highboy 95 Highboy 76 Highboy 112X Console 118X Console 41-265 Console 41-608P Console 52GC 370 LZ 512 20 Baby Grand 70 Baby Grand 71B 52B 118B 60B 84B 610B 37-89B 38-10T 38-35B 41-221CI 42-321T 46-1203 48-214 48-206 49-506
#4

If the chassis has a brass data plate riveted to the rear apron, or the tube shield on the 1931 models, then it's either an export set, or a Toronto made Philco. The U.S sets seem to have used paper labels on the chassis, with the exception of the 1928-29 models, maybe some of the 1930 sets as well. In any event I have run into variations in Canadian built Philco cabinets as well, I think one of mine was built by Thomas (or some other firm) in Woodstock, Ontario, another I saw was built by McLagan in Oshawa. Woodstock is near London, which was the H.Q of Sparton of Canada Ltd., so Thomas built a lot of Sparton cabinets, they are still in business making school busses. Philco Products Ltd. of Canada may have made their own cabinets as well, but I haven't been able to confirm or deny it, given what most manufacturers did at the time I would guess not. 
Regards
Arran
#5

Great infor thanks.  This set has a paper label on the back skirt


Attached Files Image(s)
   

Philco's: 86 Lowboy 90 Highboy 95 Highboy 76 Highboy 112X Console 118X Console 41-265 Console 41-608P Console 52GC 370 LZ 512 20 Baby Grand 70 Baby Grand 71B 52B 118B 60B 84B 610B 37-89B 38-10T 38-35B 41-221CI 42-321T 46-1203 48-214 48-206 49-506




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
The thrill is gone again, thought I was close to being done with it. Well Friday it was receiving broadcast, Saturday mo...osanders0311 — 07:47 PM
Help with Supreme 599
Iam getting closer to fixing it. I bumped Up the tranny voltage to get 5v on the 80 tube. I gan get the needle to move ...daveone23 — 03:41 PM
Philco 42-345 Restoration/Repair
Hello RodB, Checking my previous post I realized you're the one with the 42-340. I replaced the string for the tuning...osanders0311 — 03:12 PM
5U4 vs 5Z4 tubes
I saw no evidence of anything going wrong. The transformer is fused already which is nice. Interestingly the 5z4 did...bridkarl — 02:37 PM
5U4 vs 5Z4 tubes
I doubt anything cooked in 30 seconds because of the oops! These are very similar tubes, and nothing but transformer re...GarySP — 02:30 PM
Restoration of the Canadian General Electric A-87
Paul Philco322.You will be keeping very busy, you may have to go back to work for a breakIcon_smile. Paul To rel...RadioSvit — 01:57 PM
5U4 vs 5Z4 tubes
I grabbed the wrong tube and put in a 5U4 tube instead of the 5Z4 - I just had the rectifier in with no other tubes. Af...bridkarl — 01:54 PM
Restoration of the Canadian General Electric A-87
After applying the filler to the entire body, I noticed that the shades of the facade and the side and top walls were ve...RadioSvit — 01:49 PM
Restoration of the Canadian General Electric A-87
You will be keeping very busy, you may have to go back to work for a break:). PaulPaul Philco322 — 01:46 PM
Restoration of the Canadian General Electric A-87
After removing the control knobs, chassis, dynamics and scale frame, I first started restoring the torn piece of veneer....RadioSvit — 01:20 PM

[-]
Who's Online
There are currently 1044 online users. [Complete List]
» 2 Member(s) | 1042 Guest(s)
AvatarAvatar

>