Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

help me id this philco
#1

help me id this radio it has two 45s in it but the chassi i rough i do have a 112 with two 47s that is in much better condition than this one is this one has 7 tubes i think this is a 76 i might be better off cleaning it up and restoring the chassis i have also seen this model with the gril cloth like thas and also the tapestry cloth


Attached Files Image(s)
       
#2

Looks like you got you a model 76. Here's the bulletin for the 77 it's pretty much the same except for the tone circuit. Your missing the large tube shield that is fitted along the back edge of the chassis. It has the model number on it.

https://philcoradio.com/library/download...n%2013.pdf

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

The 112 chassis is similar, as is the model 76, 86, 95, 96, etc., the tube count and components are different of course. I have a model 96 downstairs, it has the push pull #45s as outputs, some models used 71As as outputs, though most were 1928-29 models. The lowboy cabinets often have damaged speaker grilles, the ones with the tapestry were later production cabinets I believe, but the one in yours isn't the worst I've seen.
Regards
Arran




Users browsing this thread:
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 2070 online users. [Complete List]
» 2 Member(s) | 2068 Guest(s)
AvatarAvatar

>