1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
cap question
ipwizard
Senior Member
****
Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek State, Province, Country: Ohio
#1

10-06-2011, 12:33 AM
I want to restuff a metal cap (non elec) it is a .50uf. The only cap I have close is a fat .47uf which will not fit inside the metal housing. Could I use two 1.0uf caps in series, or 2 .44uf caps in parallel? Im not sure what that does to the voltage value. The 1.0uf caps are only 400v, and the .22uf caps are 630v.
-Keith
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#2

10-06-2011, 12:58 AM
Two 1mFd caps in series would be 0.5 mfd, if it would fit....

Seems like I saw 0.5mFd electrolytics somewhere, they should be small enough to work in the can....
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#3

10-06-2011, 01:03 AM
Here is a link to a site that sells .47mFd electrolytics, but they are radial lead, not axial.

http://www.sterenshopusa.com/catalog/sea...CAPACITORS
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#4

10-06-2011, 01:54 AM
Two .22 caps would be fine. Still 630V.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
ipwizard
Senior Member
****
Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek State, Province, Country: Ohio
#5

10-06-2011, 11:20 AM
Sorry I wasn't clear the cap I'm trying to restuff is non-electrolytic. If I could parallel two .22 caps and get .44 and keep the voltage at 630V i'll go that route. Should be close enough to .50uf to work right?
-Keith
Find
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#6

10-06-2011, 12:37 PM
Yes, that will work just fine.
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM
Philco model 38 code 121 not receiving signal.
Good news everyone! I think I have found everything I need for rewinding the antenna coil primary. I found some pla...Stormlord5500 — 09:40 AM
Philco Battery-WWII vintage
My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM
Philco Battery-WWII vintage
Hello Bob, What Amazing find! Sincerely Richardradiorich — 10:19 PM
Testing a speaker and output transformer Trutone A2-G
Hi Murf, Do this: Monitor between ground and one plate of the rectifier while playing the radio.  Do the same with ...MrFixr55 — 09:51 PM
Philco Battery-WWII vintage
Mike; I take it that Soviet cars did not come equipped with block heaters, hence the hot oil change? Where I lived in...Arran — 08:42 PM
Philco 42-345 Restoration/Repair
The more the better. (Within reasonable limits.) 2-5 times more is no problem in this case.Vlad95 — 03:50 PM
Philco 42-345 Restoration/Repair
Thanks, RodB and Vlad95, I was mainly trying to figure out this capacitor to locate a replacement, Vlad thank you for...osanders0311 — 03:44 PM

[-]
Who's Online
There are currently 923 online users. [Complete List]
» 3 Member(s) | 920 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration