1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 610B Tone Control 30-4318 caps
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#1

10-12-2011, 11:26 AM
Hi all, Have some conflicting info on the cap values for this tone control. Both my Philco schematics(one early and one later production) list .01 and .02. I have Ray's original "Philco Condensers and More" ( Great resource book!!!) which lists a .02 and a .003 for this tone control. The Philco Repair Bench does not list this tone control. Does anyone know which would be the correct ones? I'm assuming the .02 value is correct. Thanks-Ken
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#2

10-12-2011, 02:37 PM
Those caps aren't that critical, either combination will work. Use what you have, just follow correct layout (placement). Yes, the Philco Condensers and More book is nice to have!! Best of luck with your restoration.
Find
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#3

10-12-2011, 02:56 PM
Thanks for the input. Will probably go with whats listed in the Philco schematic-Ken
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#4

10-12-2011, 09:01 PM
Go with to .003 and .02. That will give you a fair amount of difference between the two setting.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#5

10-12-2011, 11:01 PM
Yes, agree with Terry, .003 and .02 are a good combination for steps in tone.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM
Philco model 38 code 121 not receiving signal.
Good news everyone! I think I have found everything I need for rewinding the antenna coil primary. I found some pla...Stormlord5500 — 09:40 AM
Philco Battery-WWII vintage
My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM
Philco Battery-WWII vintage
Hello Bob, What Amazing find! Sincerely Richardradiorich — 10:19 PM
Testing a speaker and output transformer Trutone A2-G
Hi Murf, Do this: Monitor between ground and one plate of the rectifier while playing the radio.  Do the same with ...MrFixr55 — 09:51 PM
Philco Battery-WWII vintage
Mike; I take it that Soviet cars did not come equipped with block heaters, hence the hot oil change? Where I lived in...Arran — 08:42 PM
Philco 42-345 Restoration/Repair
The more the better. (Within reasonable limits.) 2-5 times more is no problem in this case.Vlad95 — 03:50 PM
Philco 42-345 Restoration/Repair
Thanks, RodB and Vlad95, I was mainly trying to figure out this capacitor to locate a replacement, Vlad thank you for...osanders0311 — 03:44 PM

[-]
Who's Online
There are currently 907 online users. [Complete List]
» 3 Member(s) | 904 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration