Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

How do I tell a which version 91 Cathedral I have?
#1

I got this the other day, and I am driving myself nuts trying to figure out which version this is 91A, 91B ???? I am clueless can anyone help???
Thanks
Rock


Attached Files Image(s)
               
#2

(04-19-2012, 03:21 PM)rocklandman Wrote:  I got this the other day, and I am driving myself nuts trying to figure out which version this is 91A, 91B ???? I am clueless can anyone help???
Thanks
Rock

The tag says it all. You have a U.S. Philco Model 91, Code 123.

The B stands for Baby Grand. See Ron's site here for cabinet designations: http://philcoradio.com/tech/letters.htm

By the way, if you had a Model 91A, it would say A on the tag and it would also be a Canadian version and would also indicate this as well.
Basically the power transformer is different, due to power differences back then in Canada. 25Hz instead of 60Hz mainly.

Chuck
#3

WOW!!! Thank you Chuck!!

(04-19-2012, 04:12 PM)Chuck Schwark Wrote:  
(04-19-2012, 03:21 PM)rocklandman Wrote:  I got this the other day, and I am driving myself nuts trying to figure out which version this is 91A, 91B ???? I am clueless can anyone help???
Thanks
Rock

The tag says it all. You have a U.S. Philco Model 91, Code 123.

The B stands for Baby Grand. See Ron's site here for cabinet designations: http://philcoradio.com/tech/letters.htm

By the way, if you had a Model 91A, it would say A on the tag and it would also be a Canadian version and would also indicate this as well.
Basically the power transformer is different, due to power differences back then in Canada. 25Hz instead of 60Hz mainly.

Chuck





Users browsing this thread:
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... The console body has been restored, while the varnish dries reliably I started repairing the chassis.. ...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently 939 online users. [Complete List]
» 1 Member(s) | 938 Guest(s)
Avatar

>