Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-610B?
#1

I picked up this Philco at the Kutztown show this weekend. Am I correct in that it's a 37-610B? The label's torn off. The photofinish is shot. Any recourse?

[Image: http://i863.photobucket.com/albums/ab191...-610-1.jpg]

[Image: http://i863.photobucket.com/albums/ab191...-610-3.jpg]

Larry
#2

Yes, it is a 37-610B.

--
Ron Ramirez
Ferdinand IN
#3

Only recourse would be to recreate the faux finish with paint, photo copying, or dynoc, or to use it as a marquetry experiment and put real stuff on it.
Regards
Arran
#4

Paint it like a kmart guitar and put it on ebay, should bring a grand!

John
Las Vegas, NV USA
#5

[quote] Paint it like a kmart guitar and put it on ebay, should bring a grand! [quote]

Well first you would need to get a group of friends and relatives to set up accounts and shill bid for you, then hope that the winning bidder is too stupid to notice, and hope that you covered up you misdeeds well enough not to get caught by fleabay (assuming that they actually care).
Regards
Arran




Users browsing this thread:
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 1947 online users. [Complete List]
» 1 Member(s) | 1946 Guest(s)
Avatar

>