Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

52 transitone no reception all of a sudden
#1

Hey Gang,
My 52-541 transitone has been playing really good lately, I had it on for about four hours yesterday, it all of a sudden went to loud static. no reception anywhere, volume control does work, and will silence the static.
I tried all new tubes, checked antenna connections, looked underneath for loose conections, nothin.... I unsoldered the oscillator transformer, and both IF xfmr's, all ohmed out to within .2 ohms of spec. put it back together its working...... Its been playing on the bench for the last three hours.Icon_crazy...anyone have any suggestions? is one of the xfmrs opening up intermittantly?

[Image: http://i818.photobucket.com/albums/zz105...4404c8.gif]
#2

Bad caps in the IF transformers will do that. You can troubleshoot it with the use of a signal tracer. Check for the static on either end of the IF transformers.
GL
Terry
#3

terry,
I dont have a signal tracer, yet, I'll be lookin around for one though. Are there any other tests I can do, other than just replacement?

I did open up the IF cans, very delicate stuff in there, those internal caps are very simple, and exposed to the air. It looks like a piece of paper riveted between the plastic housings. If were to replace them, what should I go with? silver mica?? What pF?

BTW the stupid thing is still playing this evening, about seven hours now....
#4

Well if you just want to replace them they are around 100-120mmfd sm. Chop out the old and solder in the new. You will need to align the IF after replacement. Should have a good sharp peak with the proper cap. Don't know of another test for them other than listening to them.
Terry
#5

Hard to troubleshoot or speculate when it is working. Could have been just a bad solder joint and you "fixed" it.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
5U4 vs 5Z4 tubes
The pinout is the same but the 5U4 has a 3 amp filament, verses 2 amps or less on the 5Z4. I think that the pinout of a ...Arran — 12:04 AM
Philco 42-345 Restoration/Repair
By the way. osanders0311 Take a look here: Dial cord stringing Guides May be here you can fount correct string settin...Vlad95 — 11:15 PM
5U4 vs 5Z4 tubes
5U4 and 5Z4 almost identical. I think nothing happened if you left 5U4 instedad 5Z4 long time. Just heater current 5U4 ...Vlad95 — 11:02 PM
Philco 42-345 Restoration/Repair
Hello Vlad95 , Very Funny ! Sincerely Richardradiorich — 11:01 PM
Philco 42-345 Restoration/Repair
RodB You are European yourself   :evil: I'm Canadian for the last 30 years  :snowman: But not Yankee  :lol: Vlad95 — 10:49 PM
Philco 42-345 Restoration/Repair
The band switch selects different oscillator coils for the band selected. I would look for a bad connection in the switc...RodB — 10:31 PM
Philco 42-345 Restoration/Repair
Hang in there...PaulPaul Philco322 — 09:30 PM
Philco 42-345 Restoration/Repair
The thrill is gone again, thought I was close to being done with it. Well Friday it was receiving broadcast, Saturday mo...osanders0311 — 07:47 PM
Help with Supreme 599
Iam getting closer to fixing it. I bumped Up the tranny voltage to get 5v on the 80 tube. I gan get the needle to move ...daveone23 — 03:41 PM
Philco 42-345 Restoration/Repair
Hello RodB, Checking my previous post I realized you're the one with the 42-340. I replaced the string for the tuning...osanders0311 — 03:12 PM

[-]
Who's Online
There are currently no members online.

>