Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-84 feet and/or back?
#1

Hi all! Can anyone please tell me what kind of "feet" the 37-84 had and if it happened to have a back? Thanks So much!
#2

Very few radios in that era had backs and the 37-84 was not one of them, if it was a 37-116 then it would have had a back. As for feet I think that it may have had short rubber feet that were tacked onto the bottom of the cabinet, some sets had thick felt pads rather then rubber ones.
Regards
Arran
#3

Don't think it had either.
Terry
#4

There was another kind that weren't really feet as such, but they were these round metal runners, about 3/8'' wide, with a felt pad crimped into the center, some were nailed on and some had a screw holding them on. If this set had those originally then they would probably still be there, they aren't the kind of thing that would just fall off.
Regards
Arran
#5

It's pretty much always OK to get a set of tack like feet with felt or rubber bottoms for a wooden cabinet radio to keep it from maring anything it is placed upon. Look carefully for tack holes where the originals might have been, if there were any. Stick on felts usually don't work out well on wooden bottom radios.




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2135 online users. [Complete List]
» 1 Member(s) | 2134 Guest(s)
Avatar

>