Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1931 Philco 112
#1

Was this model ever offered with a black finish? The reason I ask is, there one up for silent auction at our local thrift shop. I gave it a really hard look, and if it was painted after-the-fact, someone did a very professional job. (No brushmarks, runs, drips, overpaint, or other flaws). Further confusing matters, the rosette knobs on it are black, not brown, and also show no evidence of having been painted.

Mike Koste
Gobs of Knobs
Zucksville, PA
#2

Never seen one but then again, have not seen many. I have a late model low boy and they are nice sounding radios. I still prefer the styling of the 111. We need our resident experts to chime in on this one.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#3

Rosette knobs were available in black. However, I have never heard of a black 112.
#4

Some Philco models produced in 1934-35 had black rosette knobs. Model 34 comes to mind as one of these. But to my knowledge, I have never heard of a black 112 nor of any Philcos using black rosette knobs before 1934.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM

[-]
Who's Online
There are currently 1229 online users. [Complete List]
» 3 Member(s) | 1226 Guest(s)
AvatarAvatarAvatar

>