Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

MORE Phonograph Woes
#1

Anyone know where I can go to find a needle cartridge for a 1946 Philco D-10A phonograph? FYI it is mounted in a Philco 46-1209.
#2

If that unit uses a Piezoelectric, Rochelle Salt, crystal cartridge, like my 76A/46-1201, then the cartridge may also be stone cold dead.
Regards
Arran
#3

West-Tech told me they were very hard to come by.....
#4

You would pretty much have to substitute it with a more modern cartridge, or rebuild the old one, unless it is one of those magnetic types. This is part of the hold up with my Bing Crosby, that and a wonky mercury switch.
Regards
Arran
#5

I have a 47-1230 D-10A phonograph with Dynamic cartridge. If it takes the same needle, which it sounds like it does, I contacted this ebay seller and he sold me this needle... http://www.ebay.com/itm/Vtg-NOS-Philco-D...0899675089 . He might have another if you want to contact him on ebay. Warren
#6

I clicked the link but was unable to pull it up.
#7

Hmm, lets try this one.. http://www.ebay.com/itm/271292984355?ssP..._262wt_880 This one should work... contact the seller, when I got mine the auction was ended but I contacted him and he said he had more than one and sold me one.
#8

Thanks, I'll give it a try!
#9

No Problem,, I would be interested in knowing how it works out. Icon_e_smile




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1906 online users. [Complete List]
» 3 Member(s) | 1903 Guest(s)
AvatarAvatarAvatar

>