Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Speaker for a 38-62
#1

Anyone know where I can find or which model has an interchangeable speaker for a 38-62? Halfway through cap replacement but speaker is toast
#2

AJ, perhaps you can describe what part is "toast"? Field coil, voice coil, cone?
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#3

The 38-62 uses an S-7 speaker, which is also used in the following Philco models:

60
37-60
37-61
37-62
37-610B
37-610T
37-620B
37-2620B
38-9T
38-10T
38-60
38-620

--
Ron Ramirez
Ferdinand IN
#4

Thanks Ron. Jerry, the cone is toast. Looks like it picked a fight with rocky balboa
#5

AJ, if the cone is the only thing bad, no problem. Other parts are more problematic. I did a Philco 10" with a totally trashed cone for less than $3 for a cone and a little glue. Cone replacement is not rocket science, finding a proper cone, perhaps more so. There are people out there that do cone replacements.
Good luck, Jerry

PS: this is a speaker I reconed, trust me, underneath the duct tape was even worse!

[Image: http://i303.photobucket.com/albums/nn129...cttape.jpg]

This is the speaker after the $2 cone (shipping was more).

[Image: http://i303.photobucket.com/albums/nn129...001-14.jpg]

A friend in need is a pest!  Bill Slee ca 1970.
#6

Looks great jerry, where did you get the cone from?
#7

AJ sorry but lost a lot of contacts after changing computers. Perhaps others here can give you some advise on vendors, all I remember is they had a name not really related to speakers but you can google speaker cones and see what they come up. If yours is a 10" I have a cone for shipping. Cheap as they are, on a chance, buy a bunch. Not certain what you need. Fix your speaker if the rest is good. Buying an orginal even if the cone is "good" they are all suffering from age like most of us.
Best, Jerry

A little edit: Went and did a search and this is where I went for a cone. Hope it helps:

http://www.electronix.com/advanced_searc...ne&x=0&y=0

A friend in need is a pest!  Bill Slee ca 1970.
#8

AJ, how are you doing on the speaker?
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#9

Going to order a new cone in the next day or two. Just moved into my new place, first time out of the nest lol. As soon as I get everything settled I'm going to order one
#10

Hey Jerry, just for giggles did you try the speaker with the really sweet duct tape re-cone job?

Gregb
#11

Greg, it actually worked and didn't sound too bad.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#12

That's funny, its amazing how such a crude repair worked and did the job.

Gregb




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1840 online users. [Complete List]
» 1 Member(s) | 1839 Guest(s)
Avatar

>