Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
I just started rebuilding a Silvertone 101.614 chassis. The triple capacitor metal can is missing, and I know I can just replace it with three individual caps, but the three dial lamps are missing also. Does anyone know what type bulbs these are? The schematic is really hard to read. It looks like it says type 66, but I cannot find any reference to a type 66 bulb. It will be a while before I can actually power it up, so I just wanted to replace the lamps first.
Thanks in advance.
Pat
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Pat, it really helps to post a picture of the radio or at least a link to the schematic so we can help.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 205
Threads: 6
Joined: Jun 2006
City: Moundsville
State, Province, Country: WV
Pat,
After looking at a magnified schematic, I believe the dial lamp is a #44.
Carl
Northern Panhandle, WV
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 06:54 PM)jerryhawthorne Wrote: Pat, it really helps to post a picture of the radio or at least a link to the schematic so we can help.
Jerry
Sorry Jerry,
Here's the only schematic I could find.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 07:24 PM)Carl Travis Wrote: Pat,
After looking at a magnified schematic, I believe the dial lamp is a #44.
Thanks Carl,
I'll go with that. But now, I've run into another problem, thanks to an unreadable schematic.
The schematic shows two line-to-ground caps, C45 and C46. However, the chassis has one across-the-line cap, .01 @ 600V. Can I replace that with an X2 safety cap, AND and two .01 Y2 caps as well? Or should I just remove the across-the-line cap and add two line-to-ground caps, as the schematic indicates?
Pat
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
If indeed it is a 44 bulb you may want to use a 47. It runs a bit cooler. Some sets have the bulb very close to plastics dial which can be problematic. You may have seen sets with brown or black marks on the dial. Those can be burn marks from the bulb.
The voltage for the bulb is usually connected in parallel off of the heater winding on the power transformer. Where you could run in to problem is if your set powered the bulb off of the AC line though a balist tube or the heaters strung in series. Your set doesn't. In this type of circuit the voltage and current are very important. Wrong bulb can burned out( usually very quickly), damage the balist tube or other tube in that heater circuit
GL
Terry
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 07:57 PM)Radioroslyn Wrote: If indeed it is a 44 bulb you may want to use a 47. It runs a bit cooler. Some sets have the bulb very close to plastics dial which can be problematic. You may have seen sets with brown or black marks on the dial. Those can be burn marks from the bulb.
The voltage for the bulb is usually connected in parallel off of the heater winding on the power transformer. Where you could run in to problem is if your set powered the bulb off of the AC line though a balist tube or the heaters strung in series. Your set doesn't. In this type of circuit the voltage and current are very important. Wrong bulb can burned out( usually very quickly), damage the balist tube or other tube in that heater circuit
GL
Terry Even though the schematic doesn't show it, I've got three lamps in series off of the heater windings. Still use #47?
Pat
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Pat, I would follow the schematic and replace the line input with two .01mfd either "Y" or "XY" caps as indicated. Replace the existing one across the A/C line. These should be "safety caps" used in this position. They will not fail shorted which is nice across the A/C line. Many people just remove them totally. It won't hurt the radio but may increase the noise from A/C line problems.
Best, Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(10-17-2014, 08:22 PM)jerryhawthorne Wrote: Pat, I would follow the schematic and replace the line input with two .01mfd either "Y" or "XY" caps as indicated. Replace the existing one across the A/C line. These should be "safety caps" used in this position. They will not fail shorted which is nice across the A/C line. Many people just remove them totally. It won't hurt the radio but may increase the noise from A/C line problems.
Best, Jerry
Thanks Jerry,
Just the answer I was looking for.
Pat
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
Hey Pat
Are you sure the bulbs are in series?? That would mean that each bulb would have to be rated @ 2v each.
Terry
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(10-18-2014, 08:33 AM)Radioroslyn Wrote: Hey Pat
Are you sure the bulbs are in series?? That would mean that each bulb would have to be rated @ 2v each.
Terry
My error, Terry.
Maybe I need to change my medication. They are in parallel.
Pat
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
462ron
|
|
It’s on the bottom of the homepage of our Philcoradio.com homepage!
Ron462ron — 07:20 AM |
|
Model 70 Cabinet Trim
|
| Steve might have some trim left.
Not sure he is making anything.morzh — 06:12 AM |
|
Model 70 Cabinet Trim
|
| Hello musar,
First all welcome to the forum and yes that is true that steve stopped making trim .
Sincerely Richar...radiorich — 12:13 AM |
|
Model 70 Cabinet Trim
|
| I have recently come into possession of a Model 70. The trim around the base needs to be replaced. If this were years ...musar — 12:07 AM |
|
philcorepairbench.com - shadow-meter
|
| Anyone know of a way to recover these files from the repair bench? Thanks.
fenbach — 11:16 PM |
|
Philco model 38 code 121 not receiving signal.
|
| That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM |
|
Philco model 38 code 121 not receiving signal.
|
| A DMM is good enough.
One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now.
Have better volu...murf — 03:43 PM |
|
Philco model 38 code 121 not receiving signal.
|
| I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM |
|
Philco model 38 code 121 not receiving signal.
|
| I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM |
|
Who's Online
|
There are currently 234 online users. [Complete List]
» 1 Member(s) | 233 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
