Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith Transoceanic battery-opinion
#1

Hi Guys,
I am finishing up my A600 Transoceanic and once it is finished it will be for sale. My question is whether I should go through the trouble to build a battery pack(these batteries are no longer available) or just sell it to run on A/C. The battery pack will cost me about $45.00 to construct plus the cost of 10 9 volt and 4 D cell batteries.
What do you think? Since it will not be an original battery, will it still be important to a buyer/collector?

Thanks,

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#2

eric
I don`t think it would be worth it to make battery
would increase 50. to 75. more for radio
as most don`t play them often or ones that do have batteries play very little from what I seen
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#3

 If your intent is just to fix this T.O up for resale I think that making a battery pack for it is a waste of time. I don't think it would add much, if any value, to a 600 series T.O, those seem to be among the most common tube T.O models you can find. Since these were all so called "three way" portables most people would just operate them from a line cord, if they wanted one that would be practical to run from batteries they can always pick up a later transistor model T.O. 
Regards
Arran
#4

Unless you want to sell the battery you make for a profit.
But: You cannot be sure that whosoever buys it will want the battery.
And: this whosoever can buy a battery from people who build and sell them should he ever want it.
#5

Icon_thumbup Thanks guys. I tend to agree with all of you.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org





Users browsing this thread:
[-]
Recent Posts
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM

[-]
Who's Online
There are currently 1130 online users. [Complete List]
» 1 Member(s) | 1129 Guest(s)
Avatar

>