Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-650
#16

I suspect the RF coils as well. I changed the 6k7, with a new one and the stations I do get were louder and clearer. I had dismantled the sub chassis and replaced the caps, cleaned the wafer switches and rewarded some if the decayed wires a while back. After assembling it, it worked fine. Returned to it several weeks later and could not get lower stations. Thanks for the heads up. Will start on the list tomorrow
#17

Finally got this radio playing but I don't receive the lower stations. Any suggestions?
#18

See post #15.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#19

I finally got this set working again. I bought a junk chassis and interchanged tuners. I have to warn any novices, such as myself, this chassis' tuner is very difficult to repair and consider for a starting project. This was not my first project but early on found it difficult to change caps inside the tuner. After taking it apart countless times, I now have a clear understanding of how to dismantle it and replace the caps. Heed Ron's warning on this chassis. I want to thank everyone for their help, especially Terry Aka RadioRoslyn.




Users browsing this thread:
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently no members online.

>