Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Found: 38-690 Volume Control
#1

When received, my 38-690 had a replacement dual pot volume control. The issue I have is that the volume cranks up loud really fast with the control just cracked. I suspect the pot was replaced with a linear taper instead of audio taper.

Can you confirm how sensitive the volume control should be when starting from all the way down?
If what I suspect is really the case, I’ll look for a replacement through an add or Mark Opatt.

Thank you.

Tony

“People may not remember how fast you did a job, but they will remember how well you did it”
#2

What you can do is set the control @ the center of it's rotation and measure the resistance from the wiper to each end. If it's about the same it's a linear taper.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I measured both pots and they are roughly equal to wiper on each side when centered. I guess that answered my question. Before I start looking for one, would both pots be audio taper? My gut says yes.

Tony

“People may not remember how fast you did a job, but they will remember how well you did it”
#4

According to the service info the original part is 33-5240.

There's a previous discussion of that part here:
https://philcoradio.com/phorum/showthread.php?tid=13625

Quote:Part #75 is 500K and part #76 is 100K, for the dual pot.

No mention of the taper type but I'd bet on audio taper too (it is a volume control after all).
#5

Thank you guys for your help. I’ll start searching. The radio works, just has a volume control that’s too sensitive.

Tony

“People may not remember how fast you did a job, but they will remember how well you did it”
#6

Mark Oppat is making one up for me.

Tony

“People may not remember how fast you did a job, but they will remember how well you did it”




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Hi OSanders, Look carefully at the band switch. Turn it slowly and "wiggle" it around the desired band. ...MrFixr55 — 12:33 AM
5U4 vs 5Z4 tubes
I think that RCA and GE introduced metal tubes in the USA in 1936.  I don't know if they were being made by RCA, GE or b...MrFixr55 — 11:20 PM
Philco 42-345 Restoration/Repair
Vlad95, Thank you for the stringing guides and wow there are so manyosanders0311 — 06:01 PM
5U4 vs 5Z4 tubes
A pre war Hallicrafters, and an early one too, very nice! 1936 is pretty early for metal tubes too, which would explain ...Arran — 05:58 PM
Philco 42-345 Restoration/Repair
Thanks Rod, "When you hear the background hiss and no station it usually indicates that the oscillator quit" ...osanders0311 — 05:52 PM
Philco 42-345 Restoration/Repair
RodB :beerchug:Vlad95 — 10:22 AM
Philco 42-345 Restoration/Repair
Vlad, you nailed it. Swiss and German roots.RodB — 09:54 AM
5U4 vs 5Z4 tubes
Well this is a Hallicrafters SX/9 circa 1936. No real issues so far although I dodged a real bullet with a cap that was...bridkarl — 07:59 AM
5U4 vs 5Z4 tubes
The pinout is the same but the 5U4 has a 3 amp filament, verses 2 amps or less on the 5Z4. I think that the pinout of a ...Arran — 12:04 AM
Philco 42-345 Restoration/Repair
By the way. osanders0311 Take a look here: Dial cord stringing Guides May be here you can fount correct string settin...Vlad95 — 11:15 PM

[-]
Who's Online
There are currently no members online.

>