Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE model GD-60
#1

Yesterday after a disappointing trip to the Hartville Flea Martket (don't get me started on it), I stopped in at an antiques shop nearby and bought an unusual little General Electric radio. I initially mistook it for an old intercom as it looks alot like one! Turned out it is a model GD-60 am "compact" radio with five tubes and one ballast tube. Radio is complete and in decent shape, but there was one moment of panic. I pulled the chassis to inspect it and was presented with a crumpled, butchered, crumbling, and flaking asbestos pad! ARG! I grabbed a dust mask and some disposable gloves and hauled the cabinet outside for an asbestos removal. I managed to get it removed, sealed in a plastic bag and disposed of safely. If it had been intact I would have left it alone, but this thing was falling apart! Plenty of vents in the bottom of the cabinet to keep things cool though. I will have thise little guy rebuilt soon. It is kinda unique looking. Icon_biggrin

No matter where you go, there you are.
#2

cool I have many radios with asbestos lining the wood under the chassis popular problem. By the way just bought a zenith 8G625 at a flea market. Old radios are so cool!
#3

I found one of those in an antique store several years ago. It had sat in water at some time. I refinished the cabinet, replaced decals on both knobs, and worked on the chassis. Just played it a few days ago...sounds good. One of my "keepers."
#4

Mine just went out with a group of radios to be rebuilt yesterday, so hopefully I'll hear it speak soon.

No matter where you go, there you are.
#5

Nice looking set!!! If your ballast tube is open it can be replaced with a diode on this set.
Good luck!
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>