Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Unidentified Philco Radio/Record Player
#1

Recently purchased two radio/record players from a flea market one of which says Philco on the front and has a tag inside that says the radio is a philco model 740.

I've been unable to find any information on this radio and was hoping that someone here might be able to help me out.

Here's a picture of the radio in question: [Image: http://s7.postimg.org/c99ah2qd3/Philco_pic.jpg]

Any help would be greatly appreciated.

Thank you
#2

I'd take a guess and say that it is from the late 1940's to the early 1950's. Like 1948-51.
Terry
#3

You probably can't find anything because a Model 740 is a Canadian model number. Your best bet for finding that would be to find someone with a set of Radio College of Canada manuals if you want a schematic, though there maybe someone out there who has the Canadian Philco factory service data. It is from between 1948 and maybe 1952 by the looks of things, that being said radio phono consoles from that era don't tend to have much collectable appeal, if that was something you wanted to know.
Regards
Arran
#4

Hi Machinefaction,

I took a stab at searching through the Radiomuseum.org website and found what looks like your model:
http://www.radiomuseum.org/r/philco_49_1600.html

There's no photo shown, just a factory drawing. But it has most of the characteristics of your case and grille cloth placement.
A similar model (with a different case) from the same year shows a pretty accurate match to your knobs and dial glass:
http://www.radiomuseum.org/r/philco_49_1605.html

I would bet yours is a Philco 49-1600. But I'm sure there are older (and wiser) folk here on the forum who can confirm this!

Hope that helps!

Michael (mbhdesign)

mbhdesign
Michael Hennessey




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>