Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Huh? I lost the signal over 1200 AM on my 42-355!
#1

Just happened this afternoon. Anyone have any ideas on what may have failed to cause me to lose the signal on stations over 1200 AM? All the other stations before 1200 (550 - 1190) come in great, but it's puzzling to me why I can't get the local station anymore at 1470 AM, which is always the strongest signal. Any help from the experts here would be most appreciated.

Greg V.
West Bend, WI
Member WARCI.org
#2

A hair or a piece of dust sticking or whatever between the rotor and stator of your variable capacitor is your most likely suspect. Probe with a piece of paper to dislodge it.
#3

Thanks, codefox1, that's exactly what it must've been. After I cleaned out the variable capacitor, it worked like a charm. It was strange how it happened... I was listening to it this morning and it worked fine. Went to turn it back on after lunch and it was dead on the upper end of the dial. Oh well, it gave me a chance to finally set the pushbuttons to a few local stations that I'd been meaning to do for some time now, so all was not lost. I appreciate your help!

Greg V.
West Bend, WI
Member WARCI.org
#4

Yupp.




Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 977 online users. [Complete List]
» 1 Member(s) | 976 Guest(s)
Avatar

>