Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What are these Philco speakers?
#1

I traded for these for two reasons, #1: they are Philco and old; #2: I can't find another pair of these speakers online. But, I can't find a model number.

Can anyone give me a model number and approximate value?

   


Attached Files Image(s)
   
#2

As they have the Philco-Ford logo, they are no older than late 1960s. Possibly even early 1970s.

Collector value is nil to not much, I'm afraid.

If they are 32 ohm speakers, then I have a Philco AM-FM receiver that would work with them. These look very 1970s to me, though, and my receiver is a 1966 model. I probably would not have bought the receiver had I known it was designed for use with 32 ohm speakers. Icon_thumbdown

--
Ron Ramirez
Ferdinand IN
#3

See that's my problem. I can't find out what ohm they are because I can't find anything on them. Screen goes all the way around and doesn't come off. There are no numbers on them at all. Other than the Philco emblem there is no numbers or letters of any kind.
#4

Measure the resistance in ohms across the two wires coming out of each speaker box. It won't be accurate but will get you in the ballpark.

--
Ron Ramirez
Ferdinand IN
#5

The ohms on these speakers is 9.6
#6

I kind of like those, kitchy but in a early 70s cool sort of way, a perfect match for an eight track player. I don't know about these speakers but in the Criterion speakers I have the speakers point upward towards a reflector and the tops come off when you undo some screws through the sides.
Regards
Arran
#7

Radio "Shock" used to offer omni-directional speakers something like this in the early 70s.
#8

Arran,

I'd wager you are correct about the reflector inside the Philco speakers in the OP's post. Made me think of the old Harmon Kardon HK-25. I think Panasonic also made a similar speaker. Must have been popular in the 1970's.
#9

Well, they would work pretty well on any old tube amps with 16 ohm taps, and well in parallel an properly phased would do very very well an anything designed for 8 ohms in a mono setup. No guantanties on solid state gear which is much fussier.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM

[-]
Who's Online
There are currently 265 online users. [Complete List]
» 1 Member(s) | 264 Guest(s)
Avatar

>